Latch type toggle clamps GN 851.3 are compact in design and can be used to ensure high holding capacities. When closing the spanner, a safety hook positively locks onto the...Meer tonen
The rotary clamping latches GN 516 have a closing mechanism which transfers the rotary movement of the operating element resp. socket key into a 90° turn and then into a 6 mm...Meer tonen
Hinges GN 237.1 with horizontally elongated hinge wings are made in a compact and sturdy design. They are used when larger spacings are required for the fastening holes.
Hinges GN 1366 are made of rolled or drawn steel profiles and are very robust. Types A and S are fastened by welding or using holes created by the customer. Type S also has a...Meer tonen
Hinges, Plastic, White
Leveling feet GN 345 are capable of withstanding high static loads through the use of a high density plastic material coupled with a design which distributes the load over a...Meer tonen
On slotted locknuts DIN 1804 the ground surface d3 stands proud and should be used as a mating surface. Sizes M45x1,5 to M60x1,5 have 6 slots. The official DIN standard sheet...Meer tonen
Key rings GN 111.3 are suitable as universal connection elements for traction cables, ball chains, retaining straps etc. where light loads are possible. The black design is...Meer tonen
Retaining cables GN 111.2 are available in 5 different types and can therefore be used in a wide range of applications, e.g. for loss protection or as connecting and mounting...Meer tonen
The stroke of the square U-bolts of latch type toggle clamps GN 851 can be adjusted within its range. In the clamped position the square U-bolt is parallel to the fixing plane...Meer tonen
Toggle latches GN 831.2 are used for the secure holding of flaps, container lids, machine coverings and similar applications. The clamping stroke exceeds the dead centre point...Meer tonen
With extension-tapped holes of the semi-split shaft collars GN 7062.1, sensor holders GN 7062.10 or other elements such as the gear lever or cam can be attached to shafts and...Meer tonen
The thrust point of the stainless steel grub screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller...Meer tonen
Leveling feet GN 41 are for use in aggressive environments. The range of combinations of base plates and adjustable spindle versions allows these leveling feet to be used in...Meer tonen
Leveling feet GN 32 will be delivered mounted and are not removable.
Leveling feet GN 439 are used for installing smaller machines, systems or devices. Thanks to the rubber underlay, they have a damping, noise-reducing effect and prevent surface...Meer tonen
The influence of a washer on the quality of the screwed connection is very often underestimated. With washers GN 6339, high quality preloaded screwed connections can be...Meer tonen
Load rings GN 5860 rotate running in ball bearings. The freely rotating ring allows the bolts to hold loads in any tensile direction. The rated load-bearing capacity is shown...Meer tonen
T-nuts GN 50i fasten attachments and accessories in the slot of aluminum profiles. The spring-loaded ball secures the T-nut against unwanted slipping within the slot, making...Meer tonen
Square U-Bolts, Steel
Spring plungers GN 615 are used as detents as well as for push-on and push-off applications and ejectors.
With spring latches GN 722.2, the plunger pin is retracted over the curve of the guide by a 180° turn of the latch. The notch at the upper end of the curve causes the latch to...Meer tonen
Latches GN 515 are identical to standard latches GN 115 except for the extended housing. They are operated with a rotation limited to 90°, which moves the latch arm into the...Meer tonen