Pointed stainless steel sheet metal hinges GN 1364 are characterized by their compact and universal dimensioning as well as their attractively shaped design. The materials used...Meer tonen
Connector pieces GN 880.1 are required when using oil drain valves GN 880. Screwing on the connector piece will activate the valve plate of the oil drain valve, allowing the oil...Meer tonen
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table. The eye nut must be of fully screwd in to...Meer tonen
Multiple-joint hinges GN 7231 are installed on the inside of flaps, hatches and doors to save space and ensure protection against vandalism. The hinges have a maximum opening...Meer tonen
Art.-Nr.
1486025
Leveranciersnummer
614-6-NIS
EAN
4045525749252
Aantal
1 stuk
A special feature of oil level indicators GN 650.1 is that the liquid level is visible even from the side. The polyamide body consists of two parts which are ultrasonically...Meer tonen
Toggle latches GN 761 are especially suited for rapid closing and fastening of covers, container lids and boxes. When the lever is closed, the eccentric configuration of the rod...Meer tonen
Latch type toggle clamps GN 852.3 are compact in design and can be used to ensure high holding capacities. When closing the spanner, a safety hook positively locks onto the...Meer tonen
The rotary clamping latches GN 516 have a closing mechanism which transfers the rotary movement of the operating element resp. socket key into a 90° turn and then into a 6 mm...Meer tonen
Ball buttons GN 249.1 are mainly used with spring plungers when low wear and exact positioning are needed. To achieve optimal locking of the spring plungers, the maximum...Meer tonen
Knee lever modules GN 810.12 have the same properties and attributes as the „Longlife“ GN 810.10 / GN 810.11 heavy duty vertical acting toggle clamps: The clamping arms are...Meer tonen
Art.-Nr.
1466644
Leveranciersnummer
127-ZD-76-60-HB-SR
EAN
4045525573536
Aantal
1 stuk
Hinges GN 237.1 with horizontally elongated hinge wings are made in a compact and sturdy design. They are used when larger spacings are required for the fastening holes.
Hinges GN 122.1 with indexing positions keep the door in the three specified positions without additional mechanism. In indexing position the loosening torque is 1.1 Nm (test...Meer tonen
Hinges GN 129.3 are used for doors which are flush with the frame on the outside. Once assembled, they cannot be unhinged. The hinges are fastened with socket cap screws DIN...Meer tonen
Art.-Nr.
1476819
Leveranciersnummer
237.3-NI-80-80-B-GS
EAN
4045525538672
Aantal
1 stuk
Hinges, Plastic, White
The hinges GN 154 consist of two different wings of unequal length. They are preferably used when thick walled doors or door profiles have to be screwed on to thin walled housings.
Art.-Nr.
1191330
Leveranciersnummer
236-75-60
EAN
4045525519978
VPE (Verpakking)
2 stuk
Aantal
1 stuk
Art.-Nr.
1217878
Leveranciersnummer
136-ST-40-40-B
EAN
4045525852617
VPE (Verpakking)
10 stuk
Aantal
1 stuk
Art.-Nr.
1217880
Leveranciersnummer
136-ST-50-50-B
EAN
4045525852624
VPE (Verpakking)
10 stuk
Aantal
1 stuk
The static load of the leveling feet GN 343.5 is limited by the load capacity of the ball joint (AISI 303). The static load values in the table refer to a net vertical load in...Meer tonen
Leveling feet GN 344.2 feature a conductive ESD plastic material (PA) or rubber (NBR) which prevents static charges from building up. The imprint ESD-C on the surface of the...Meer tonen
C-Washers GN 183 maybe installed without the removal of the nut from the stud. In terms of dimensions they are almost identical to C-Washers DIN 6372.