Art.-Nr.
1478793
Leveranciersnummer
351-30-20-M8-ES-40
EAN
4045525574977
Aantal
1 stuk
Retaining magnets GN 50.25 are combined with the stainless steel housing and the plastic ring into a system that shields and strengthens the magnet for optimal transmission of...Meer tonen
Hinges GN 128.2 are produced from drawn weldable profiled stainless steel extrusions. The pin is fixed in the lower half.
The clamping bore of flanged connector clamps GN 145 is mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462. Flanged connector...Meer tonen
Art.-Nr.
1210342
Leveranciersnummer
638-18-M8-35-ST
EAN
4045525471771
Aantal
1 stuk
Retaining magnets GN 50.45 are combined with a stainless steel housing and a plastic ring / insulation ring into a system that shields and strengthens the magnet for optimal...Meer tonen
The retaining magnets GN 51.3 with rubber jacket form a system together with the steel part that shields and strengthens the magnet, optimally concentrating the magnetic flux on...Meer tonen
Split shaft collars GN 707.2 correspond in measurement to the semi-split shaft collars GN 706.2. They are used when an axial assembly is not possible. These shaft collars can...Meer tonen
Mini indexing plungers GN 822 are distinguished for their small dimensions. They have been designed for installation in thin walled sheet metal constructions. In type C, the...Meer tonen
Stainless steel shoulder screws ISO 7379 are cost-saving construction elements for a wide variety of different uses. The maximum tightening torque is limited by the relatively...Meer tonen
Rubber buffers GN 356 provide elastic support for equipment such as compressors and pumps. The tapered shape absorbs side forces better compared with cylindrical rubber buffers....Meer tonen
Stainless steel hinges GN 235 are adjustable in height or width along the slots, depending on the design, and are fastened with hex-head, oval-head or cylinder screws with a low...Meer tonen
The folding handles with recessed tray GN 425.8 are used if the handle is to protrude by a maximum of 3 mm when folded down. In type A, the folding handle is held in both end...Meer tonen
Hinges GN 1366 are made of rolled or drawn steel profiles and are very robust. Types A and S are fastened by welding or using holes created by the customer. Type S also has a...Meer tonen
When flow indicators GN 655 are used, a rotor rotates above a minimum volume flow rate Q, depending on the medium and its viscosity. The flow rate is visible from all sides....Meer tonen
The breather filters GN 884 are used when the air exchange is to be allowed between the inside of the container and the ambient air. The stainless steel wire mesh prevents...Meer tonen
High-strength, cranked shackles GN 585 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen
High-strength, straight shackles GN 584 are made in analogy with the US Federal Specification RR-C-271 and feature sixfold safety standards, which means that the minimum failure...Meer tonen
Indexing plungers GN 608.1 with rest position are used for such applications where the plunger has to stay in its retracted position. To achieve this, the knob is rotated by 90°...Meer tonen
Stainless steel spherical washers and dished washers DIN 6319 are used for clamping on non-parallel surfaces. Thanks to the material used, the spherical washers and dished...Meer tonen
Stainless steel spring plungers GN 614 are used as detents as well as for push-on and push-off applications and ejectors. A tolerance of H7 for the location hole of d1 is...
The PFB patch is a jamming thread locking (Polyamide patch). The coating for Type K or KN (standard spring load) is indicated blue, for Type KS or KSN (high spring load) green....Meer tonen
The clamping bore of flanged connector clamps GN 146.3 is mechanically machined and designed for construction tubesGN 990 or DIN 2391, DIN 2395 and DIN 2462. Flanged connector...Meer tonen
Construction tubes GN 990 can be supplied in these standard lengths. The tolerances specified for the outside diameter of the round construction tubes comply with the...Meer tonen